Packaging Details
- Unit Type: lot (10 pieces/lot)
- Package Weight: 0.800kg (1.76lb.)
- Package Size: 8cm x 5cm x 3cm (3.15in x 1.97in x 1.18in)
Free shipping 10pcs/lot 12V24V36V 10A Pulse Width PWM DC Motor Speed Controller Switch protected alarm LED Current limiter control
/piece
/piece
/piece
/piece
/piece
/piece
/piece
/piece
About CCMCP:
Main Usage:CCMCP widely use to people DIY, hobby, scientic test, such as control computer Ipad fan speed, control bulb, control motro kymco, control xbox360, HHO Pluse Width modulator, Tes Equipment, industrial automation, speed regulator module board support PLC, motor electric pump fan speed control, PWM HHO RC controller,remote control toys, etc......
Features
- CCMCP Motor Speed Regulator controls the speed of a DC motor by adjusting Pulse-Width-Modulated (PWM).
- Provide smooth variable speed capability for DC motor
- Adjustable current limit. Current limit can be adjustable 1A to 10A.
- Include Power-on LED and current-limit-protected alarm LED
- The input supply voltage speed range is DC12V-36V
- Duty Cycle adjustable range is 0%-100%.
- Internal operating frequency is 21kHz.
- Potentiometer cable length is 20cm
Specifications:
- Item size: 3.4*2.1*1.1 inches ; Net Weight:2.5 ounces
Operating instruction:
1. Connect your DC motor (or DC load) to the motor terminals as indicated on the wiring diagram.
2. Connect a voltage of 6V-28V DC to the circuit making sure of the correct polarity of the connection. Note that the voltage applied to the motor will be supply voltage applied to the circuit.
It is recommended to add an
appropriately rated fuse in line with the positive supply in order to protect the circuit from any possible short circuits.
3. You can now control the speed of the motor through potentiometer.
Positive inversion switch is used to control the motor speed direction. And the center position of positive inversion switch will cause the motor to stop.
Important Notes
Operating instruction:
Before you attempting to wire the controller, make sure power is off.
WARNING: DO NOT REVERSE POSITIVE AND NEGATIVE POWER LOADS.THIS WILL DAMAGE THE CONTROLLER
1. Connect wires refer to the “wiring diagram” (NO.4 picture).
2. Adjust the current limit as you need.(The factory setting of current limit is 1A)
3. Turn on the power, and adjust the potentiometer.
4. The green LED lights, the power is OK.
Current Limit Adjustment:
When the red alarm LED is lighting, the trim pot should be reset as follow:
1.Turn off the power.
2. Adjust the trim pot until the desired maximum current is reached.
3.Wait for about 3 seconds, than reset the power .
In Case of Difficulty:
If a newly installed control will not operate, it is likely that a terminal or connection is loose.
Check to make sure connections are secure and correct.
If the control is still inoperative, refer to the following chart for reference:
PROBLEM | POSSIBLE CAUSE(S) | CORRECTIVE ACTION |
Motor doesn’t run | Incorrect or no power Potentiometer set at zero Worn motor brushes Current limit set too low | Install proper service Rotate the potentiometer fully CW Replace motor brushes Adjust current limit trim pot CW |
Motor runs at “full speed” uncontrollable | Loose potentiometer connections Possible control failure | Secure all connections Contact us returns policy |
Motor rotates in wrong direction | Motor wire hooked up backwards | Reverse motor wire + and - |
Motor stalls under a light load | Current limit trim pot improperly adjusted | Adjust the trim pot properly |
Package Including:1 x DC Motor Speed Controller
Terms and Conditions
Shipping:
· Shipping to most other countries takes about 10-30 days via Economy Int\'l Airmail without tracking#. In rare case, it can take up to 40 days. It depends on your location and local postal service(e.g., Russian Postal service is slow), as well as the weather condition along the shipping.
· Please verify your primary shipping address. We are not responsible for any wrong or undeliverable addresses.
· Express mail: Extra 20 USD-25 USD will be charged for the first 500 grams. Contact us if you need this service.
· Full refund can be offered if you\'re out of patience after 30 days. But PLEASE do not leave us poor ratings.
Payment:
· We accept payment via Paypal. Western Union, T/T.
· Please pay your invoice in 4 days after auction ends.
· The buyer is responsible for any applicable import duties and local taxes. Usually there\'s no any charges for small parcel. But please verify with your customs before making your purchase.
Contact Us:
· We take full responsibility if you receive wrong item or damaged item or item not as describled.
· If you\'re not satisfied for any reason, please feel free to contact us. Just send us an message or email. You can always get our solution pretty soon in our working time.
· Your satisfaction is guaranteed.
About UG:
Thank you for choose UG. We Will Be No.1 In China!
As a manufacturer of electronic module, UG have been in business more than 20 years, and therefor have wide experience in all the line we handle.
To Be No.1 Supplier Of Electronic Module In China !
Different From Other Similar Products In Ali Express, Our Factory Use High Quality Potentiometers Only!
Always Imitated, But Never Surpassed In China.
If You Find Other Suppliers Price Lower Than Us, Quality Higher Than Us, Please Let Us Know, We Are Going To Beat Them!
OEM Service Also Welcome!