Product features:
Interface design, there are five USB port, the Type - C, 20, MicroUSB, Type - A1, Type - A2.
Easy to use, wide range of application
High efficiency and reliability
Portable mobile power module
Digital tube power display
Product parameters:
Battery type: lithium polymer battery
Maximum output power: 65W/100W
The default is digital tube power display
Motherboard has 5 USB port by default, the Type - C, 20, MicroUSB, Type - A1, Type - A2.
In addition, the DC port can only charge, but cannot discharge. Input 5-12V.
Lightning supports PD2.0 fast charge input.
Type C supports an AFC/FCP/SCP/VOOC/PD3.0 / PD2.0 quick charge input.
Support of PPS/PD3. O/PD2.0 AFC/FCP/QC3 + / QC3.0 / QC2.0 / SCP quick charge output.
Type-A1/Type-A2 supports fast charge output For Apple/AFC/FCP/VOOC/QC3+/QC3.0/QC2.0/SCP.
MicroUSB supports AFC/FCP/SCP fast charge input.
Type-C supports input/output bidirectional fast charging.
The input supports 5V/9V/12V/15V/20V voltage.
The PPS output supports 3.3V-21V/3A.
PD3.0 / PD2.0 output support 5 v3a / 9 v3a / 15 v3a 12 v3a / / 20 v5a.
QC2.0 output supports 5V3A/9V3A/12V3A.
QC3.0 supports 5V-12V output voltage, 200mV/Step.
AFC output supports 5V3A/9V2A/12V2A.
The input supports 5V/9V/12V voltage.
FCP output supports 5V3A/ 9v21/12v1.5a.
The input supports 5V/9V/12V voltage.
SCP output supports 5V4.5A and 10V2.2A.
5.5V3A is supported.
VOOC output support 5V@4A.
Supports simultaneous discharge of TypeA1 / TypeA2 /Type-C ports.
Maximum 5V@3A, to fast charge please single port use.
Product size: 72x27x6mm
Note:
1: The motherboard external battery line must be able to pass 10A current, at least with more than 1 square copper wire, ordinary line to use 1.5 square. It doesn`t have to be too thick, but it shouldn`t be too thin. Too thin could be a safety hazard. (because there is a lot of current at the battery end)16AWG cable is recommended.
2: The motherboard comes with a protection chip, only support 2-5 series of batteries, 6 series of lithium iron phosphate need the battery comes with a protection board, with the protection board over current protection current must be greater than 15A, otherwise it can not work properly, seriously damage the motherboard chip.
3: Because the current at the battery end is too large, the battery must be welded with a thick wire to test. The charging and discharging can not be tested by holding the welding pad with an alligator clamp. Be sure to do so this shop refuses after-sales service.
4: Select the battery can use 4.15V/4.2V/4.35V/4.4V 18650, polymer, ternary lithium battery, large monomer can be used, single battery capacity does not exceed 25000mAh, more than the power display will be inaccurate. 3.65V lithium iron phosphate is supported, but disposable dry batteries, nickel-metal hydride, nickel-chromium, and lead-acid batteries are not supported. The minimum battery string is 2, the maximum battery string is 6, and the total voltage cannot exceed 23V. The charge and discharge flow of a single series battery should be at least 10A. If the charge and discharge flow cannot reach 10A, turn down the power.
5: The motherboard must be preset battery capacity, please see the details inside the introduction.
6: Supports OPO flash charging and HW super fast charging. Different protocols have different power. 65W and 100W are the power of PD protocol, and 20W for VOOC and 22.5W for SCP. Please confirm the demand before shooting, do not accept or support your phone can not be charged quickly on the return. Welded goods do not support return or replacement. (Phones that are not supported are not available to third parties because the phone has its own protocol.)
7: This motherboard connected to the battery must meet the requirements and to series, if your battery is ordinary capacity small current single or multiple parallel battery please refer to other types of motherboard.
8: the battery connected to the motherboard line must be thick, the battery must be able to more than 10A current does not heat.
Product list:
1X module