|
aHR0cDovL2ZyZWVzaGlwLmNvLmty
- ÀÛµ¿ ¼Óµµ: 24000rpm
- ÃÖ´ë ÅäÅ©: 0.65N.m
- ½Åû: ¹Ð¸µ
- ¸ðµ¨ ¹øÈ£: 1.5kw ER16 Metal Spindle
- µå¶óÀ̺ê: MOTOR
- ºê·£µå À̸§: G-PENNY MACHINE
- ±Ù¿ø: CN (Á¤Ç°)
- Size: 80x226mm
- Voltage: 220v
- Current: 7A
- Power: 1.5kw (1HP=735w)
- Cooling: Water Cooled
- Bearings Material: Ceramic Ball Bearings
- Bearing Type: 2 X 7004 P4 DT & 2X 7002 P4 DT
- Collet: ER16
- Frequency: 400Hz
- Pole: 2
- Collet Range: 1-13mm (Including 1/4,1/8,1/2)
1 & 220v 1.5kw ER16 Metal Working Spindle Motor Water Cooling Diameter = 80mm
Size:80x226mm(Middle body diameter:80mmxLength:226mm)
Speed Ways:Through 3-phase output inverter and adjust the inverter frequency to change the spindle speed.
Cooling:Water cooling
Power Interface:Optional H20-4 pins waterproof air plug. The air plug marked "1 ","2"," 3"," 4", "1 ","2 ","3" were connected to inverter (U, V, W), 4 connected inverter ground.
Power:1.5kw
Voltage:220v
Current:7A
Frequency:400Hz
Speed:24000rpm
Pole: 2
Runout Off:Less than 0.01mm
Diameter(mm):80
Bearing Type:2 x 7004 P4 DT & 2 x 7002 P4 DT
4pcs Ceramic Ball Bearings (fully sealed angular contact bearings)
Collet:ER16
Clip Knife diameter:13mm,12mm,12.7mm,11mm,10mm,9mm,8mm,7mm, 6.35mm,6mm, 5mm, 4mm, 3.175mm, 3mm, 2mm, 1mm(standard 6mm)
Water Cooling ER16 collet chunk
Grease Lubrication
Main Application:Engrave for iron,steel,stainless steel, aluminum,hard wood etc.(This is professional metal spindle, high accuracy,big torque)
There are 4 labyrinth seal in the front section of the spindle,prevents lubricant leakage from bearings and intrusion of harmful impurities (dust, moisture, corrosive gases) and bearing seals under high-speed conditions.
Ceramic ball bearings,full sealed angular contact ball bearings ,2×7005C P4 DT&2×7002C P4 DT,increase spindle life.
Carefully assembly make the spindle more precisional.
High accuracy,used for metal engraving,cutting.Precision 0.01mm.
We are the spindle manufacturer,we offer only best quality and best price to you.
Our Ceramic ball bearings spindle use 4 pcs ceramic ball bearings.
Ceramic ball bearings are resistant to high temperatures and low heat, usually 3-5 degrees lower than steel ball bearings during using .
Ceramic ball bearings have low friction, low noise and long service life.
1. Why the inverter manual with the inverter is Chinese?A: Sometimes we put the Chinese manual with the inverter, but we have the manual in English of PDF files, please contact us for English manual. Also we offer the basic setting video, please contact us.
2.What is the difference between the wood working spindle and metal working spindle ? A: Metal spindle use the iron shell, so the rigidity is better and the torque is bigger. If you use wood working spindle for hard metal, the inside bearings will broken in 1-2 month,But if you use metal spindle,it can works well and for a long time.
1. Spindle working environment temperature is usually -10 ~ 40 .
2. Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon. 1.Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter`s specifications and parameter settings need match spindles parameter.
2.Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.
3.It should ensure that before use of water-cooled spindle, the cooling system is working properly. Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.
1.Water cooled spindleMUSTbe used with water pump. Otherwise the spindle will soon broken.
2.AC spindle motorMUST use with inverter. The power of inverter need equal or bigger than the spindle power. Before using,please set up the inverter parameters suitable for spindle. Otherwise the spindle and inverter will broken at once.
3.When you use the spindle,the noise is not same as always,pleaseSTOP the spindle at once. You may need to replace the spindle bearings.
If you don`t know how to set up the inverter or connect the spindle to inverter,please contact us.We will help you to set up it.
Before shipping , we did the oil seal to avoid the rust during the long shipment. When you get the spindle, please clearing the oil seal before using. Thank you.
Spindle from the production - assembly - test, and finally the perfect packaging .
We will 100% guarantee security to the hands of the guests.
Shipping Cost
Our products are sold worldwide.
If you need many items in the same time, please contact us in advance to confirm shipping cost.
Payment:
We accept paypal credit, bank transfer, western union etc.
Payment must be made within 7days calendar days of the auction end time.
Problem and Feedback:
PLEASE DON`Tleave any negative feedback before you contact us.
We are honest and helpful supplier , we will try our best to solve problems with you.
Your satisfaction is very important for our store, so please contact us before you want to leave a negative feedback.
Thanks very much in advance.
Refund:
If you areNOT SATISFIEDwith our package like the products is damage, please do not sign it and contact us immediately.
If it is possible, please take some photos or make a small video about it. It will help us to solve the problems.
Note:
We can produce the product according to our customer`s design.
If you need something is very special, please contact us about it.
We are willing to help you about it.
|
|
|
|
|