Attachment:
Frame 1 set
1 pneumatic motor
Twist Chuck 6
1 torque adjusting wrench
1 air tube
1, new tapping machine products, driven by compressed air, safe, fast and efficient. 2, the average pressure and volume (5-8kg /cm2), large torque output. 3, can be a variety of steel, iron, copper, aluminum, plastic and other materials for tapping. This faucet doesn`t break easily. 4, the cylinder is equipped with overload protection device, tapping damage is small, high precision teeth. 5, simple operation: hold the motor, align the hole, long press the start button and start tapping, tapping into the required depth, long press the exit key, tapping the head automatically exit, complete a tapping operation. 7, heavy products do not need positioning device or mobile device, with ten thousand head can be easily completed. 8, fast positioning, cutting speed, increase output. 9, through hole or blind hole, tap will not be damaged, pneumatic tapping machine safe tapping blind hole with twist clip barrel tapping, automatic sliding, protect the tap head, high precision tapping, to ensure high precision tapping. Rapid and repeated positioning allows continuous tapping operation on a workpiece, eliminating the inconvenience of readjust the position of the workpiece each time the old tapping machine taps. Wide range of working activities, universal head, can ensure no spiral Angle.
Preventive measures :1. For your safety, please read the operation manual carefully and operate the machine according to the safety instructions to avoid accidental damage caused by misuse. For proper use, place it flat, not high, to prevent degradation from affecting the function of the parts. Corrosive chemicals are placed on the rubber base so as not to affect the fastness of the machine. Do a good job of cleaning each time, in order to maintain the life of the machine, especially the two grinding holes are the most important, if not clean, will indeed make parts wear, and affect the grinding accuracy. First, adjust the vertical direction :1. Make the quick change joint at the bottom of the pneumatic motor contact with the table or the workpiece plane, the quick change joint and the table, vertical (quick change joint and the table has no clearance), and then lock the four fixing screws of the vertical plate or universal head. 2. The air duct connector is located at the connection between the motors. 1. Press the front end of the pneumatic motor, and the motor is "triggered" by rotation; At the same time, gently press the "reverse button" of the rear pneumatic motor to reverse the car. Before you quit your job. 2, the parallel arm can easily move to the tapping position, without the need to force down tapping, just like the guide screw in and out of the screw hole as the resistance is small. 1. The intake pipe must be 3/8 inch or more than 10 mm, and the length should not exceed 10 meters. Set the pressure at 4-8kg.
Accessories: Frame 1 set 1 pneumatic motor 1 air source processor wrench 61 torque adjustment wrench 1 trachea 1, new tapping machine products, driven by compressed air, safe, fast and efficient. 2, the average pressure and volume (5-8kg /cm2), large torque output. 3, can be a variety of steel, iron, copper, aluminum, plastic and other materials for tapping. This faucet doesn`t break easily. 4, the cylinder is equipped with overload protection device, tapping damage is small, high precision teeth. 5, simple operation: hold the motor, align the hole, long press the start button and start tapping, tapping into the required depth, long press the exit key, tapping the head automatically exit, complete a tapping operation. 7, heavy products do not need positioning device or mobile device, with ten thousand head can be easily completed. 8, fast positioning, cutting speed, increase output. 9, through hole or blind hole, tap will not be damaged, pneumatic tapping machine safe tapping blind hole with twist clip barrel tapping, automatic sliding, protect the tap head, high precision tapping, to ensure high precision tapping. Rapid and repeated positioning allows continuous tapping operation on a workpiece, eliminating the inconvenience of readjust the position of the workpiece each time the old tapping machine taps. Wide range of working activities, universal head, can ensure no spiral Angle.
Preventive measures :1. For your safety, please read the operation manual carefully and operate the machine according to the safety instructions to avoid accidental damage caused by misuse. For proper use, place it flat, not high, to prevent degradation from affecting the function of the parts. Corrosive chemicals are placed on the rubber base so as not to affect the fastness of the machine. Do a good job of cleaning each time, in order to maintain the life of the machine, especially the two grinding holes are the most important, if not clean, will indeed make parts wear, and affect the grinding accuracy. First, adjust the vertical direction :1. Make the quick change joint at the bottom of the pneumatic motor contact with the table or the workpiece plane, the quick change joint and the table, vertical (quick change joint and the table has no clearance), and then lock the four fixing screws of the vertical plate or universal head. 2. The air duct connector is located at the connection between the motors. 1. Press the front end of the pneumatic motor, and the motor is "triggered" by rotation; At the same time, gently press the "reverse button" of the rear pneumatic motor to reverse the car. Before you quit your job. 2, the parallel arm can easily move to the tapping position, without the need to force down tapping, just like the guide screw in and out of the screw hole as the resistance is small. 1. The intake pipe must be 3/8 inch or more than 10 mm, and the length should not exceed 10 meters. Set the pressure at 4-8kg.